Bambu Lab Textured PEI Plate — H2C (330 × 320 mm)

Bambu Lab Textured PEI Plate — H2C (330 × 320 mm)

This is the full-size textured PEI build plate made for the Bambu Lab H2C — 330 × 320 mm of powder-coated PEI on magnetic spring steel, matching the printer's maximum footprint corner to corner. It's the plate most H2C owners print on day in, day out: PLA and PETG stick without glue, parts release with a flex once the bed cools, and every part bottom comes off with a clean matte texture that hides layer artefacts and fingerprints.

A build plate is a consumable. The coating wears where you print most, and a scrape or a stubborn nylon part can take a patch out of it. Having a second plate on the shelf means you pull a finished print off, drop a fresh plate in and start the next job in seconds — which is the whole point of a magnetic plate in the first place. Workshops, classrooms and small production benches usually run two or three.

---

Why this plate

• Strong first layers without the fuss. The textured powder coating gives PLA, PLA-CF, PETG, ABS and ASA a mechanical key to grab onto — no glue stick, no brim gymnastics, no first-layer babysitting.
• Full H2C build area. 330 × 320 mm of usable surface, so you can use every millimetre the H2C offers for big single parts or dense plates of small ones.
• High-temperature rated. The surface is rated to 180 °C, which covers the 90–110 °C bed temps that engineering materials like PC, PA and ASA want.
• Double-sided. Both faces are coated — flip it when one side starts to show its miles and you've effectively got two plates.
• Tool-free swaps. Drops onto the H2C heatbed magnets and locates on the rear stops; lift it out with the front tabs when the bed has cooled.
• Prints come off cleanly. Let the bed drop below about 40 °C, lift the plate out and flex it — parts release instead of needing a scraper leaned on them.

330 × 320 mm Double-sided PEI Up to 180 °C Glue-free PLA & PETG Magnetic spring steel FAP035

---

Who it's for

• H2C owners who want a spare so the printer never sits idle waiting for a plate to cool.
• Small businesses and print farms running back-to-back batches — swap plates, restart, deal with the parts later.
• Schools and makerspaces where plates get handled by lots of hands and a backup matters.
• Anyone replacing a worn plate after a few hundred hours of PETG, nylon or the odd over-enthusiastic scrape.
• A2L owners — the same 330 × 320 mm plate fits that printer too.

---

What's in the box

• 1 × Bambu Lab Textured PEI Plate, 330 × 320 mm (FAP035), textured PEI coated on both sides
• Protective packaging — no tools, glue or adhesive sheets are included or needed for installation

---

Materials & bed temperatures

Bambu Lab's published bed temperatures for the Textured PEI Plate. Most materials need nothing but a clean surface; only TPU, PC and PA benefit from a thin coat of glue stick as a release layer.

Material	Bed temperature	Glue
PLA / PLA-CF / PLA-GF	45–60 °C	Not needed
PETG / PETG-CF	60–80 °C	Not needed
PET-CF	80–100 °C	Not needed
ABS / ASA	90–100 °C	Not needed
PC / PC-CF	90–110 °C	Recommended
PA / PA-CF / PAHT-CF	90–110 °C	Recommended
TPU	35–45 °C	Recommended
PVA	45–60 °C	Not needed

Looking after it

• Wash with warm water and a drop of dish soap when prints start lifting — skin oils are almost always the culprit. Dry fully before printing.
• Never use acetone or other organic solvents on a PEI coating; they attack the surface.
• If adhesion drops after heavy use, a light scuff with 600-grit sandpaper will restore the texture's grip.
• Let the bed cool before removing parts — releasing a hot plate is what chips coatings.

---

Specifications

Model / part number	Bambu Textured PEI Plate — FAP035
Usable print size	330 × 320 mm
Compatible printers	Bambu Lab H2C (also fits A2L)
Surface	Textured PEI powder coating, both sides
Coating thickness	0.075 mm
Substrate	Magnetic 301SEH stainless spring steel, 0.4–0.5 mm
Max surface temperature	180 °C
Colour	Gold
Mounting	Magnetic, tool-free
Shipping weight	Approx. 0.74 kg